04 Jan 06, 12:21 pm
god where do i start
81 chevy 3/4ton started stock sb350 th350 np208 and weaker axles with wopping 3:42 gears in them, put a 6" bds suspension lift on it and some 35s, wasnt satisfied and wanted more... parked it almost 2 years ago and started tearing into her, as she sits she has no engine no tranny no tcase no bed no front axle and no hood installed... what i have for it now to be put on/in 327 small block fresh rebuild, doing about 330 est. hp, has a truck avenger carb, holley intake, accel super coil, and yeah... sm465 transmission, np203 tcase, ORD tcase doubler kit, ORD triple stick shifter kit, ORD High Steer kit, Energy Suspension polyurethane bushing kit, DANA 60 front end with some kind of magic happening in it, dunno what all i know is theres clutch packs??? 42 inch super swampers (squeeking the fit on this one), bucket seats, 4 point harnesses, and i think thats it so far...
what i have installed HA, 8" superlift/procomp suspension kit, some wonderful stainless steel brake lines, GM 14 bolt FF rear axle needs new gears, but i have installed the ORD disc brake kit on it, uh and thats it...
what i need so dearly, 2wd chevy steering box, np205 tcase, at this point i dont care what it was mated to as long as it was a chevy, i can change the input shaft for all i care, need to get some ubolts for the front axle because youngs is yeah (might order from BTF) i need to regear the rear axle, get an exhaust system of some sort, do a manual transmission linkage swap thingy, figure out how the brakes go on the 60, get pads, get hubs for the 60 and then i can be done!!! and drive the sob!!!
and sometime in the far future ive thought about 4linking the rear end... i think it would be fun to try...
81 chevy 3/4ton started stock sb350 th350 np208 and weaker axles with wopping 3:42 gears in them, put a 6" bds suspension lift on it and some 35s, wasnt satisfied and wanted more... parked it almost 2 years ago and started tearing into her, as she sits she has no engine no tranny no tcase no bed no front axle and no hood installed... what i have for it now to be put on/in 327 small block fresh rebuild, doing about 330 est. hp, has a truck avenger carb, holley intake, accel super coil, and yeah... sm465 transmission, np203 tcase, ORD tcase doubler kit, ORD triple stick shifter kit, ORD High Steer kit, Energy Suspension polyurethane bushing kit, DANA 60 front end with some kind of magic happening in it, dunno what all i know is theres clutch packs??? 42 inch super swampers (squeeking the fit on this one), bucket seats, 4 point harnesses, and i think thats it so far...
what i have installed HA, 8" superlift/procomp suspension kit, some wonderful stainless steel brake lines, GM 14 bolt FF rear axle needs new gears, but i have installed the ORD disc brake kit on it, uh and thats it...
what i need so dearly, 2wd chevy steering box, np205 tcase, at this point i dont care what it was mated to as long as it was a chevy, i can change the input shaft for all i care, need to get some ubolts for the front axle because youngs is yeah (might order from BTF) i need to regear the rear axle, get an exhaust system of some sort, do a manual transmission linkage swap thingy, figure out how the brakes go on the 60, get pads, get hubs for the 60 and then i can be done!!! and drive the sob!!!
and sometime in the far future ive thought about 4linking the rear end... i think it would be fun to try...