Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Update your rig status here!
I got my new brake lines installed, pulled the front driveshaft going to re do it tomorrow.
Reply
New brake lines are installed and brakes bled, I think the front brake calipers had some air in them because now that they have been bled I have a lot more brake pedle, The new long travle square driveshaft is all bolted in, I took it on the road and suprisingly I dont get any drive line vibration till i get it over 45MPH, I figured with the driveshaft made out of square tube it would vibrate like heck on the road. as usuall james was a big help on the driveshaft project. Up next will be shock hoops then 4 Link. I talked my wife into an aussie locker for my birthday Big Grin
[Image: IMG_1248.jpg]
[Image: IMG_1249.jpg]
Reply
New axle joints and diff fluid changed all out and as usual all of this was done in jeffs garage Big Grin
Reply
XJ made about a 50 mile round trip today. Farthest it's been in a while. Lots of driveline vibrations as usual. Actual work and such "should" begin this week on the bumper.
Reply
WJ has sprung another problem, I now have a leaking rear axle seal in it too Sad
Reply
got this for the TuRD today

[Image: IMG_1254.jpg]

Bye Bye stupid carburetor and manual steering :whistle:
Reply
Angler Wrote:Bye Bye stupid carburetor and manual steering :whistle:

Hello I/M office. Cool
Reply
-45* F 1, Suzuki 0

Suzuki in heated garage overnight = still no start. :banghead: Cry Confusedhrug:

2 hours of troubleshooting, several phone calls and an acetylene torch later :yes:

I guess if someone put a torch to me I'd start moving faster as well. :eek:
Reply
The Talon got 4 new valves and a headgasket this weekend. Passed I/M, registered and soon to be on the market.
Reply
akdsmer Wrote:Hello I/M office. Cool

It's a good thing no one here knows anyone in the I/M department :troutslap:
Reply
akdsmer Wrote:Hello I/M office. Cool

nope, going be registered in florida
Reply
Angler Wrote:nope, going be registered in florida

Doesn't matter where its registered, still needs I/M. Or you could wait until the program goes away :whistle:Big Grin
Reply
ajpthng Wrote:Doesn't matter where its registered, still needs I/M. Or you could wait until the program goes away :whistle:Big Grin

well the truck is IMed till aug 08 we deploy aug/sept 08 Unless the I/M Ninjas busts into my garage and hauls the poor TuRD away I think I will be good, the IM program will problibly be gone by the time I get back and even then, I wont be in alaska much longer after that.
Reply
but hows Ryan going to wheel it with expired tags????
Reply
ARCTIC_EXPRESS Wrote:but hows Ryan going to wheel it with expired tags????

Ha ha she will be to busy laying on the beach in florida to worry about wheeling anything but a cooler to the dunes
Reply
jeep- gone

FrankinTuRD-
parts ordered

front shocks-Ron
New front axle- Wayne
flex joints- suicide doors
4link brackets- ballistic fabs
High steer, diff armor, axle truss, knuckle rebuild kit,Chrome Moly Birfields, wheel spacers,- Foothill Off road.

Just waiting on the UPS man now Big Grin
Reply
Well, zero calls this weekend about my TJ.

I drove my ZJ home yesterday. 4 hr trip. It's got bumpsteer, too much air in the tires, and 3 oil leaks. I love that thing.
Reply
Z's definately have some advantages.

I was doing some calculations and my ZJ is doing a little better than I was gathering previously. I do have to say that with 4" of lift, 31's aired up to 30 PSI, etc, the Zj has a smooth ride.
Reply
Drove it to work today, too.
Tell me my father-in-law didnt' tow my camper 4k miles in 4th gear?! I've got a shudder between 1rd and 2st gear. :mad:
Reply
Got body cut off of 4runner, james laid eyes on the donor cab, i orderd the locker for front, and axle vent extentions today.
Reply
sevenslats Wrote:Drove it to work today, too.
Tell me my father-in-law didnt' tow my camper 4k miles in 4th gear?! I've got a shudder between 1rd and 2st gear. :mad:

Time to find an AX-15 and get rid of Chrysler's gift to the Grand Cherokee world.
Reply
changed the water pump and thermostat on the TuRD today
Reply
Got the shock mounts built, shocks are installed, aussie locker, knuckle rebuild kit are here, going to pick up new front axle from Wayne tomorrow, still waiting on diff armor and front axle truss, and chrome moly shafts, then I can put the front axle together
Reply
74 blazer ( marks old one ). put new heater in and it works great. has new door locks, cd player now, speakers in the doors, and a new batt. new tires are in the works and rims. plan to cut the rust out and add fender flares, winch, steering colum, seats out of the 91 unless sold before then. upgrade to axel shafts front and rear. just alot of little work here and there needs to be done.
Reply
Needs fluids filled/changed.

Otherwise it's just fine...the locker seems to be acting better, guess it hates -40 as much as I do.
Reply
XJ: Snapped front ujoint and axle shaft. Brake issue again. Steering issues getting worse.

Dodge: Heater working again, still need to make an appointment with Gene's to get the ps fixed and the other issues taken care of.
Reply


Forum Jump:


Users browsing this thread: 6 Guest(s)