Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Wrench or Wheel this weekend
I got the two front tractor R1 tires fitted up with tubed inside, 32 bolt beadlocks are not my favorite thing to tighten down.
i also got my housing r/p down to kevin in delta. not long before I start putting the front back together on the blazer. I need to buy a welder too. ..
Reply
I wheeled and wrenched this weekend. Now next weekend I'm not sure what I'm doing.
Reply
Who is doing what this weekend? I'm trying to figure out whether I'm going to try to work on the XJ and take a trip, take a trip and go fishing somewhere south, or work around the house. With the heat I really don't want to work around the house. Me and heat don't get along very well.
Reply
I've decided to watch 5 kids from Friday night till Monday.

Gonna clean the shop, I hope.
Reply
I will be working around the house. Maybe drop a fuel tank
Reply
Correction, installing a transmission first thing Saturday, I hope.
Reply
I will most likely be installing a new cam on Saturday.
This will include using a cam degree wheel, which is kind of a cool process if you've never done it;
it actually 0's in when your cam is truly at tdc.

That is if I don't get an ambulance call - on call till 8 A.M. Sunday.

So Mel, you could come down here with your fishing gear, see the process and then go fishing!
Or go fishing if you get here and I end up with a call.
Reply
Wish I had seen this earlier. Made plans for a buddy to come over and help me with some work around the house. But if something changed I may head down there.
Reply
If you do come down this way, stop by Mark's and grab the cam and oil he forgot to bring me!
Reply
tore down a ford 60.
inspected it.
looks good.
need to pop the cover and carrier. .. ill let kevin work his magic on that one later Big Grin
Reply
Sorry didn't make it down. But did get alot done around the house that I've putting off.
Reply
bringing this one back from the dead.
Installed free spin hubs on my DD.
Solved a few annoying squeaks on my DD.

Had some troubles with the grease gun.
Grease gun - 4
peter - 1

(I eventually won)
Reply
Anyone wanna do a short run Saturday morning?
Gilmore trail area to stay away from hunters? There are a couple of places...all easy.
Reply
I can't do Saturday, i have to help my wifes friend move.
Reply
Im game. Dont have any plans set in stone all weekend.
Reply
Repp?
Gilmore?
Both?
Other ideas?
Reply
I rode repp on my dirtbike last weekend and it was just a dirt road. It has been raining quite a bit so it might be better. I can go check either tomorrow or friday and report back
Reply
Inlaws are in town.
Reply
I'll be loading my rig and the trailer up for another hunting trip.
Reply
So is anyone wheeling Saturday the 31st or Sunday the 1st? I got the hole truck bed lined finally and want to test it out to see how it holds up.
Reply
good to have a full sized rig ready to rock Big Grin
mine.. is just a rock at the moment.
Reply
I'll be putting up firewood for the winter this weekend. I'll have my truck with me in NP, so I may be up for hitting Repp in the evening.
Reply
The inlaws are out, so lets wheel! I am game for anything close.
Reply
I went and checked out repp this morning on my quad. I only rode the half after the pipeline and it really wasnt bad at all. The last little slough crossing is really the only potential tough part. Im up for running it on saturday though.
Reply
Zukman Wrote:The inlaws are out, so lets wheel! I am game for anything close.
how about behind the airport?
Reply
I will be wrenching this weekend when the wife is not tasking me with stuff to do.

I need to finish K9 motor install and exhaust on Mac.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)