Update your rig status here! - Printable Version

Update your rig status here! - Printable Version

+- Arctic Offroad Forums (http://www.arcticoffroad.com)
+-- Forum: Talk (http://www.arcticoffroad.com/forumdisplay.php?fid=3)
+--- Forum: General 4X4 (http://www.arcticoffroad.com/forumdisplay.php?fid=9)
+--- Thread: Update your rig status here! (/showthread.php?tid=120)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

Update your rig status here! - 78calico - 14 Jun 10

Two functioning winches on BIGBOY = 27,000LBS of pulling power. :yes:
54,000LBS with snatch blocks. I wonder if I could pull the truck in half.:eek:

Thanks for all the help Mel.

Update your rig status here! - ak_petey - 14 Jun 10

I think Mel gets the helper of the weekend award!

Update your rig status here! - akram - 14 Jun 10

I can't wait to see the whole rear bumper get finished. It actually looks decent with just the winch mount. Glad to help.

Update your rig status here! - ak_petey - 21 Jun 10

GOOD news. inner tube, staun diaper, spare wheel, spare tire are all in. just a matter of days before I get them. I am going to pick up some e brake cables and linkages/parts tomorrow . .. after the tires and ebrakes are set in place I will meet the club requirements for trail rides. ..

now I just have to figure out how to lower the blazer 2-3 inches to be road legal.

Update your rig status here! - 78calico - 22 Jun 10

I modified my bedside, tranny pan, gas tank, front diff cover, tie rod, and draglink.
And the only tools I used were big rocks.:whistle:
I also emptied my fire extinguisher and modified a FRS for use underwater.:lol:

It was an awesome week.

Update your rig status here! - big_bad_jeep - 22 Jun 10

sounds like yall had a great time.. i sure hope next year i can make it.

Update your rig status here! - ak_petey - 22 Jun 10

hehe bent tie rod = penguin foot stance.

Update your rig status here! - 78calico - 22 Jun 10

ak_petey Wrote:hehe bent tie rod = penguin foot stance.

Not bad enough to be visually noticeable by the wheels but it does bind when the suspension articulates.

Update your rig status here! - Zukman - 26 Jun 10

New rear diff installed , New caster shims (pinion now points at T-case output now), new rear axle u-bolts too. Noisy rear was broken center pin in rear diff.

I want to thank Don, Mark and Mel for helping me out on this!

Update your rig status here! - ak_petey - 27 Jun 10

Ebrake installed,
Shifter boot installed,
tools put away,
spare tire in the back of my blazer,
watching the boards for the next trail ride.

Update your rig status here! - ak_petey - 29 Jun 10

top of blazer painted!
[Image: 062800_205600.jpg]

Update your rig status here! - 78calico - 29 Jun 10

LOL. There is no giving the police choppers the slip now.

Update your rig status here! - ak_petey - 29 Jun 10

hahaha. .. i top out at 60 ish mph. .. i dont think a chopper is necessary to catch me!

Update your rig status here! - AKMark - 29 Jun 10

A Christmas tip netted me a manual crank tailgate for FREE!!! Just need to knock out a dent and install a new piece of glass.

Gonna try to get the interior put back together and need to install the underhood wiring and heater box so I can install the front clip prior to the move.

If I get the time, I will put the new rear end in, but I doubt I will get the time prior to the move.

With this tailgate, and the odd colored doors and front clip, I'll be rivaling old Calico for most multicolored truck soon.

Update your rig status here! - big_bad_jeep - 29 Jun 10

there is a k5 a the transfer site by ur place there.

Update your rig status here! - AKMark - 29 Jun 10

That's where I got this.

Update your rig status here! - ajpthng - 13 Jul 10

Well here is what I started with,

[Image: dsc00972.jpg]

This is what I did,

[Image: dsc00978.jpg]

This is the test fit,

[Image: dsc00975.jpg]

I have to do some trimming of my rocker guards as it makes contact with the tube flare so I couldn't get it to match up correctly and as you see I was running out of daylight.

Update your rig status here! - akram - 13 Jul 10

Nice work Tom. Keep the pics coming.

Update your rig status here! - Fix_It - 13 Jul 10

fix what i broke ...

Update your rig status here! - ak_petey - 14 Jul 10

git 'r' dunnnnnn

Update your rig status here! - ajpthng - 14 Jul 10

I didn't get much done today but here is the difference between the stock fender and the highline fender. Keep in mind I'm running 36" tires

[Image: img00067-20100714-2051.jpg]

Update your rig status here! - ak_petey - 14 Jul 10

that is a lot of room!

Update your rig status here! - big_bad_jeep - 15 Jul 10

how much did they run for ya???? i would like to get a set for my jeep

Update your rig status here! - ajpthng - 15 Jul 10

The fenders were $550 but I also got the inner fender mounting kit for $160 and the LED lights I think were another $60. I think shipping ran me right around $50.

http://www.genright.com/

Update your rig status here! - ajpthng - 15 Jul 10

Pass side set up, tomorrow I will be working on the hood then prep for paint.

[Image: dsc00983.jpg]

Update your rig status here! - ak_petey - 15 Jul 10

what is the wall thickness on the tubing? pretty sturdy? I have a friend who made his own, but a rock ate them up on a roll.. well more like a mean lean.