Update your rig status here! - Printable Version

Update your rig status here! - Printable Version

+- Arctic Offroad Forums (http://www.arcticoffroad.com)
+-- Forum: Talk (http://www.arcticoffroad.com/forumdisplay.php?fid=3)
+--- Forum: General 4X4 (http://www.arcticoffroad.com/forumdisplay.php?fid=9)
+--- Thread: Update your rig status here! (/showthread.php?tid=120)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

Update your rig status here! - sevenslats - 16 Mar 07

... I need my own ****ed-up thread.

Update your rig status here! - naturalbornmudder - 16 Mar 07

update for lil' T:

It is holding together faithfully thus far. The exhaust is loose at the manifold. Tightening it doesnt seem to help much.

I replaced the rear track bar bolt. That made the ride nicer.

My rear diff cover is leaking from somewhere, so it will be time to get back into the rear diff and tinker around soon.

If the engine and tranny hold together for 6 more months, I will consider myself blessed. In a perfect world I would be able to go pick up a bare bones 03 TJ with 4.0L and NP3500 tranny, and transfer all of my goodies to it and sell the red carcass for 500 dollars, but I just checked my wallet and that is a big no-go Big Grin

Update your rig status here! - sevenslats - 16 Mar 07

naturalbornmudder Wrote:... the red carcass...

Update your rig status here! - AKMark - 16 Mar 07

Update on the Burb;

Found a way to finance the engine rebuild. I will wait till the funds have been verified, then I will work on getting the motor out and apart. Hopefully if all is well, it will be broken in prior to meet and greet.

Got way too much to do on the FSJ before then as well.

Update your rig status here! - Advent - 16 Mar 07

naturalbornmudder Wrote:The first statement and the second statement seem to contradict each other.

When you say perfectly acceptable, perfectly acceptable for who? Also a desert rig can be wider in front than back because it isnt serving daily driver status from Noth Pole to Eielson every day on icy roads with side wind gusts.

How do they contradict each other? I said it's fine if the front is made wider than the rear. I didn't say the method it was done is fine.

If you drive around LA you'll see an awful lot of those desert trucks with wide fronts and stock rears. They don't seem to have any problem. I've seen quite a few of them in Anchorage too. Heck, Wayne was going to do that kind of setup on his Tacoma.

Update your rig status here! - naturalbornmudder - 16 Mar 07

either way, I'll bet that the axle width difference in Geoff's rig is causing his unpredictable handling when changing lanes and driving to work, plain and simple.

Update your rig status here! - ajpthng - 16 Mar 07

I finally got the BB installed on the WJ,

Before,
[Image: 2596187_3_full.jpg]

After

Before,

After,

Nothing special but it sure looks better.

Update your rig status here! - akram - 17 Mar 07

Looks nice Tom.

The toyota finally has a gas tank that fits. It got new (used) bucket seats and the radio is wired and needs mounted someway. Now I can enjoy driving it a little more once the XJ goes under the knife.

Update your rig status here! - 2T2 - 18 Mar 07

orderd coil overs. and upper a arms. have the main brace installed for the tire carrier. will have pics in about a week or so

Update your rig status here! - Darkchild1723 - 18 Mar 07

Atlas II Installed,
Rear Driveshaft installed,
waiting on Skid, front yoke, and front axle performance seals to get in
Have new block Heater I need to install
Need to change my Front R&P after I pick it up from Holeproof
I have to cut my Shifter back down because I eliminated my belly-pan spacers

Update your rig status here! - ChevyKev - 18 Mar 07

Have a nice puddle of PS fluid under my truck.
Chevy ordered the wrong ball stud for my clutch linkage.
Have the correct ones on order.

May actually work on mine this week a bit - change to the amsoil fluid I've had for it for about 8 months now. :whistle:

Update your rig status here! - crazy4ink - 23 Mar 07

OK, here are some pics that I snapped yesterday in the shop...

What my Jeep looks like this week:
[Image: P3210001.jpg]

Kenne Bell layed out prepped for the install:
[Image: P3210002.jpg]

Update your rig status here! - ChevyKev - 23 Mar 07

Got the correct Ball studs for my clutch linkage - and installed one of the two I got!

Also fixed the PS leak (hose had come off the metal line, even though the clamp was still tight and the metal tube is flared! :eek: It was replaed, with 2 clamps. I also refilled my empty PS resevoir with the Amsoil synthetic tractor hydraulic fluid and it seems to be working well.

I couldn't find the exhaust gasket I need to replace, so I tightened the collector bolts up for my Tuesday trip. Then pulling into the visitor center I found the gaskets in the glove box. (I'm only typing this so I will remember where they are!)

With all that done, I found a reoccuring problem yesterday of one of my hubs not engaging. I think there is moisture in there that is preventing it from locking in as this happens only when it sits for long periods of time with the hubs unlocked. Tuesday when I came home from the trail ride I drove in 2wd, hubs unlocked and parked it overnight. Then Thursday I noticed the hub wouldn't re-engage. Need to clean and re-pack bearings.

Update your rig status here! - mousee - 23 Mar 07

Haven't posted here in a while...
Mousee is getting closer. Have the rear tube framwork almost done. getting ready to start the four link pretty quick.

Update your rig status here! - ChevyKev - 23 Mar 07

mousee Wrote:Haven't posted here in a while...
Mousee is getting closer. Have the rear tube framwork almost done. getting ready to start the four link pretty quick.

:nopics:

Update your rig status here! - mousee - 23 Mar 07

Shoulda seen that coming...

Here ya' go.

Basically for those that don't know, I chopped the frame and are back halving it with tube. 18" fox airshocks, and four linked rear and three linked front. Moving the gas tank into the "bed" for more clearance. 1" heims on the lower end of the links and either(haven't fully decided yet) 3/4" heims or 1" uniballs on the uppers.
[Image: 10224d1174608980-mousees-build-finally-s5000728.jpg]

[Image: 10224d1174608980-mousees-build-finally-s5000728.jpg]

[Image: 10228d1174608980-mousees-build-finally-s5000733.jpg]

[Image: 10225d1174608980-mousees-build-finally-s5000729.jpg]

Update your rig status here! - ChevyKev - 23 Mar 07

red x's are interesting, but still no pics.

Update your rig status here! - Fix_It - 23 Mar 07

still sanding and prepping for paint on the 67 .. until you have actually done paint prep .. you dont realize how much work it is .. i have been sanding for 4 days now and im still on the drivers side @ 150 grit and i was told i need to be somewhere in the 320 grit range :mad:

but the axles are rebuilt ,new brakes and soon to be mounted new floors and seats ..

i have not touched the bumpers or roll cage yet thats the fun stuff !

Update your rig status here! - mousee - 23 Mar 07

I can see 'em. can anyone else?

Update your rig status here! - Advent - 23 Mar 07

mousee Wrote:I can see 'em. can anyone else?

Nope. I don't think jeeps-offroad allows image linking.

Update your rig status here! - naturalbornmudder - 23 Mar 07

i see em

Update your rig status here! - akram - 24 Mar 07

I don't

Update your rig status here! - TJVigilante - 24 Mar 07

It must be for JO members only.

See sig. :p

Update your rig status here! - akram - 24 Mar 07

I'm a member of JO and can't see them.

EDIT: After opening Jo I can now see them.

Looks like fun work.

Update your rig status here! - TJVigilante - 24 Mar 07

cookies my man, cookies.

Update your rig status here! - mousee - 27 Mar 07

Okay, I figured I would try to post up some more red x's for ya'll. I am trying this on AO, so bear with me...

[Image: attachment.php?attachmentid=154&stc=1&d=1175054207]

[Image: attachment.php?attachmentid=154&stc=1&d=1175054207]

[Image: attachment.php?attachmentid=155&stc=1&d=1175054207]

[Image: attachment.php?attachmentid=156&stc=1&d=1175054207]